Author Topic: Arduino based PWM diversion control system  (Read 17087 times)

WillEert

  • Full Member
  • ***
  • Posts: 151
Re: Arduino based PWM diversion control system
« Reply #135 on: May 07, 2018, 08:44:26 AM »
The only thing about OnStar is if you do not pay for the diagnostics package then perhaps they might get the data but you and Chevrolet does not...... Using OnStar charging can be turned on and off as they choose, whoever "they" are. I suspect this is a move towards V2G. Sometimes I consider drilling a hole through the antenna or otherwise disabling it as I am not a big fan of the big brother is watching you concept. 

Will the Luddite
(1) 24 ET 185 mono, Classic 150,8x Surrette 6CS25p, 3x Magnum 4448, homecooked diversion system;
(2) 15 Heliene 330 mono, Classic 150; (3) 2 X 6 Hansol 345 mono, 2 stand alone Hotspot ACDC12C Mini-split heat pumps.

ClassicCrazy

  • Hero Member
  • *****
  • Posts: 1861
Re: Arduino based PWM diversion control system
« Reply #136 on: May 07, 2018, 08:54:52 AM »
Not sure where the antenna is located or access to it but disconnecting the coax to the antenna would work. Or wrapping the antenna in tin foil will make it ineffective. Keep in mind that if you disconnect it , some agents may come knocking on your door ! ha ha .

I know someone who has a Tesla and that car is always hooked up to Tesla central command.

Larry
« Last Edit: May 07, 2018, 08:57:10 AM by ClassicCrazy »
system one
Classic 150 , 5s4p  Kyocera 135watt , 12s Soneil 2v 540amp lead crystal for 24v pack , Outback 3524 inverter
system two
Classic 150 ,5s 135 watt Kyocero , 16s Calb 100AH LiFePO4 , Outback VFX 3648 inverter
system three
Midnite KID MPPT 24 DC in to  12 volt AGM batterie

Westbranch

  • Hero Member
  • *****
  • Posts: 2680
  • Building System (sort of) 1 weekend at a time
Re: Arduino based PWM diversion control system
« Reply #137 on: May 07, 2018, 10:54:30 AM »
A friend with OnStar in his truck found out the hard way a few years ago, when  not on a "scheduled" (numbered) Highway in BC, that OnStar rescue service does not work without cell service.... that may be the reason they did not contact you about a bad battery....??

Thanks for the link to the battery issue..
KID FW1811 560W >C&D 24V 900Ah AGM
CL150 29032 FW V.2126-NW2097-GP2133 175A E-Panel WBjr, 3Px4s 140W > 24V 900Ah AGM,
2 Cisco WRT54GL i/c DD-WRT Rtr, NetGr DS104Hub
Cotek ST1500 Inv  want a 24V  ROSIE Inverter
OmniCharge3024  Eu1/2/3000iGens
West Chilcotin 1680+W to come

WillEert

  • Full Member
  • ***
  • Posts: 151
Re: Arduino based PWM diversion control system
« Reply #138 on: June 01, 2018, 07:47:57 PM »
I think I will continue my car battery adventures in the batteries section.

Will
(1) 24 ET 185 mono, Classic 150,8x Surrette 6CS25p, 3x Magnum 4448, homecooked diversion system;
(2) 15 Heliene 330 mono, Classic 150; (3) 2 X 6 Hansol 345 mono, 2 stand alone Hotspot ACDC12C Mini-split heat pumps.