Kid endamps: Section under construction???

Started by SolarMusher, July 06, 2014, 08:20:46 AM

Previous topic - Next topic
Print
Go Down Pages1
User actions

SolarMusher

July 06, 2014, 08:20:46 AM
I've just finished to install a small 12V system with the new kid (production unit) and WBjr here : 415Ah AGM Surrette, 470W PV with Magnum 2812 on epanel. When time came to tune the kid, I looked for endamps value in the different menus. I finally found it, pressed enter and saw an interesting "SECTION UNDER CONSTRUCTION"... After going through the different menus, I noticed that the WBjr SOC was doing its job nicely. I had updated this kid to the last FW (1722 I think).
So my question would be: Is  there really no EA setting (WBjr + Shunt) at this time on the kid or am I missing something???
Thanks
Erik
Off Grid with 4kw PV | 2x Classic 200/WBjr | 2x Outback VFX3648 Epanel | 3x SPD300 + 1x Schneider HEPD80 | Hub + Mate + PSX-240 | Volthium 400Ah/51.2V LFP battery bank + Trimetric | 1500 watts AC water heater | Kubota 11kw GL diesel generator

Mario

#1
July 07, 2014, 07:40:38 PM
The end amps is now functional on the unit, read the Manual about functionality and Shunt selector kid vs wbjr shunt.
The website list 1722 as the latest revision as you mention but the latest firmware is 1742, we will get that fix as soon as we can mean while I will attach the latest revision here sou you can update your unit.

Thanks,
Mario

SolarMusher

#2
July 08, 2014, 08:11:07 AM
Hi Mario,
Thanks for the update but a little late.
This kid is now installed at the customer's cabin and is running on time only, 80km/2 hours away from me...
Erik

Off Grid with 4kw PV | 2x Classic 200/WBjr | 2x Outback VFX3648 Epanel | 3x SPD300 + 1x Schneider HEPD80 | Hub + Mate + PSX-240 | Volthium 400Ah/51.2V LFP battery bank + Trimetric | 1500 watts AC water heater | Kubota 11kw GL diesel generator

jcfaber1

#3
July 10, 2014, 10:00:58 PM
I have a production unit and the firmware is pre 1722.  Which firmware should I install the 1722 or the one posted by Mario here.  I have a 260 watt panel and am charging 2 6v AGM 225 AH batteries wired in a series in a little tear drop camper.  Thanks

John

chris

#4
July 11, 2014, 12:06:34 AM
Quote from: Mario on July 07, 2014, 07:40:38 PM
The end amps is now functional on the unit, read the Manual about functionality and Shunt selector kid vs wbjr shunt.
The website list 1722 as the latest revision as you mention but the latest firmware is 1742, we will get that fix as soon as we can mean while I will attach the latest revision here sou you can update your unit.

Thanks,
Mario

  Is this a new update?   I havent seen 1742...an I think I'm running 1741
System 1
12 volt system,
280 AH DIY LifePO4 with 200amp JBD BMS
4x200 Watt 36volt panels 4P
MidNite Kid, WBjr
2000 watt Kisae SW inverter

System 2
Off Grid RV (parked and used as a cabin)
12 volt system,
4 X T-105+
6X100 watt array wired as 3 strings
MidNite Kid, WBjr & MNBTS
1500 watt Cotek SW

Mario

#5
July 14, 2014, 05:46:49 PM
Firmware Revision 1742 is the latest release, it is now also located in the Firmware tab of our website.

Mario

SolarMusher

#6
July 17, 2014, 08:29:18 AM
Quote from: Mario on July 14, 2014, 05:46:49 PM
Firmware Revision 1742 is the latest release, it is now also located in the Firmware tab of our website.

Mario
Mario,
Is WBjr end amps on shunt part of this latest release?
Erik
Off Grid with 4kw PV | 2x Classic 200/WBjr | 2x Outback VFX3648 Epanel | 3x SPD300 + 1x Schneider HEPD80 | Hub + Mate + PSX-240 | Volthium 400Ah/51.2V LFP battery bank + Trimetric | 1500 watts AC water heater | Kubota 11kw GL diesel generator

Mario

#7
July 17, 2014, 05:16:52 PM
yes 1742 includes EndAmps from WBJR,
refer to the Manual on how to set it up.

Mario
Print
Go Up Pages1
User actions