Local App BETA software version 0.3.22

[Halfcrazy]

Ok here is the Beta version of the APP it is version 0.3.22 

https://dl.dropbox.com/u/31975941/LocalStatusPanel.v0.3.22.air

Here are the changes in this version
- add Follow-Me
- add bts-net
- Fixed in Hydro mode under the Tech Menu the Minimum input voltage
is   off by a factor of 10. The Classic shows 1v and the App shows 10V
- Fixed MPPT voltage does not write at all in Hydro mode
- IP controls now active.
- you can now read configuration values without entering the password.

[Halfcrazy]

This will likely be the last update unless we find simple issues. Andrew and Rey will be devoting all there resources to My MidNite and the Web Server that will reside on MidNite products. Please do point out anything that pops up and Andrew will keep a running list.

Ryan

[Resthome]

Ok here is the Beta version of the APP it is version 0.3.22 

https://dl.dropbox.com/u/31975941/LocalStatusPanel.v0.3.22.air

Here are the changes in this version
- add Follow-Me
- add bts-net
- Fixed in Hydro mode under the Tech Menu the Minimum input voltage
is   off by a factor of 10. The Classic shows 1v and the App shows 10V
- Fixed MPPT voltage does not write at all in Hydro mode
- IP controls now active.
- you can now read configuration values without entering the password.

No mention of the disconnect issue many of us experience while in the data tab. Thought Andrew was also working on a solution to this. Any progress on this issue?

[TomW]

I still have the issue where my "live data" only shows data from Nov of 2012. on my older Classic and the date in the box next to the pop up calendar says 03/11/2013 but the graph is Nov 1 2012

On the newer Classic I simple get "No data available" for the time it has been in use but somehow there is data from before it even got commissioned?

I did not see others with this so may be my dated "AIR" on Ubuntu so I have not brought it up much.

Had this issue with every Local App version I tried.

Don't waste time on it because it is probably the AIR version I have.

I have not seen the dropped connection bit since the previous version here.

Just FYI.

Tom

[Halfcrazy]

Unfortunately Andrew ran into several snags on the Logging so we are going to revisit it later.

Ryan

[MikeJ]

After update not showing live data now it is  just a stright line at 0

On edit... everything seems to work but the Input current,Battery current and watts
Mike

[Lya72]

Hi,

So Ryan, for my understand, this Beta version has Logs problems ? And the precedent is better ?

Secundo, How do we interpret the charge status from the export Logs File ?

Yann

[Halfcrazy]

No this logging is the same as the last one no better no worse. I will check into charge stage interpretation

Ryan

[Lya72]

Hi Ryan,

A little UP for the following information :

I will check into charge stage interpretation.

Thanks in advance.

Yann

[Halfcrazy]

Here is a list of what we think it should be. Keep in mind this is not verified

0 = Resting     
3 = Absorb     
4 = BulkMppt   
5 = Float       
6 = FloatMppt   
7 = Equalize   
8 = PvShade     
9 = Over Load     
10 = HyperVoc         
11 = Wake up Count Down
12 = Arc Fault
13 = Ground Fault
16 = Current Limit Reached
17 = Unit Is HOT
18 = Eq Mppt     

[dbcollen]

and the one I get most evenings

28  Relay Error

[SolarMusher]

Ryan,
I still have triple data entries on the 0.3.22 beta Loc App soft this morning, I'm still with 1181FW in the Classic.
Would the last Beta Classic FW solve this issue?
Erik

[Halfcrazy]

Yes, The issue is the Classic and as far as we know the new Beta Classic firmware has resolved this issue for everyone.

Ryan

[SolarMusher]

Thanks Ryan, I'm going to install this beta right now .
Erik

[boB]

and the one I get most evenings

28  Relay Error

dB, Did you update your firmware recently ?  I can't remember...   This error I believe it usually left over from a non-relay error
and is probably bogus.   That's one of those very strange software anomolies that sorta evades a good explanation.

boB