I did a clean reinstall of the local App on my laptop now I cant even connect with my classic over the local home network.
I have had it working like a champ for monthsover the local home network and even working fine monitoring remotely online. Now I would be happy even if I could just get it to work over the local network.
I have classic set on static ip 10.0.0.10 and I can see the classic on my network by y logging into my modem and its showing the some ip on the classic LCD. I also double checked the ip using the Fing program and its also showing the classic online on my local network at 10.0.0.10 and port 502.
So I open the local App enter 10.0.0.10 and and it comes up with (connecting) then (retrying) and (unknown) above the IP address .
So I have gone back to basics and I am just trying to get the local app to at least work over the local home network but I am struggling with that at the moment for some reason.
Is there any more to the picture something silly I am overlooking as i can see it on my network but just cant connect with it through the local app?
I am seeing error 2002 coming up even on a fresh install.
Kurt
Quote from: offgridQLD on April 19, 2013, 07:25:29 AM
I have classic set on static ip 10.0.0.10 and I can see the classic on my network by y logging into my modem and its showing the some ip on the classic LCD. I also double checked the ip using the Fing program and its also showing the classic online on my local network at 10.0.0.10 and port 502.
Local networks should be on a 192.168.x.x network, internal routers, wifi routers and most other devices not assigned specific ip numbers or class c networks or subsets of them by your ISP will expect to use a 192.168.x.x network.
Quote
So I open the local App enter 10.0.0.10 and and it comes up with (connecting) then (retrying) and (unknown) above the IP address .
The wifi router or LAN router you have will be trying to route this connection to the Internet where the real 10.x.x.x class A network is
Quote
So I have gone back to basics and I am just trying to get the local app to at least work over the local home network but I am struggling with that at the moment for some reason.
Is there any more to the picture something silly I am overlooking as i can see it on my network but just cant connect with it through the local app?
Look on your router and see what network it is using for LAN routing. It's probably something like 192.168.1.1, so try setting your classic to 192.168.1.80 static address, netmask 255.255.255.0
Quote
I am seeing error 2002 coming up even on a fresh install.
#2002 is back again, make sure you have the latest adobe Air version although even this makes many #2002 error messages
Dgd
dgd;
Sorry, you are dead wrong. 10.x.x.x is a legit private IP according to RFC 1918. See this for the others:
https://en.wikipedia.org/wiki/Private_network (https://en.wikipedia.org/wiki/Private_network)
Just for clarity and accuracy.
Tom
Have you tried rebooting the Classic?
Quote from: TomW on April 19, 2013, 08:42:17 AM
dgd;
Sorry, you are dead wrong. 10.x.x.x is a legit private IP according to RFC 1918.
You are right, I'm usually wrong.
Strange how routers here go to the local ISPs dns server to resolve this address, I was thinking that unless Kurt had used a 10.x.x.x on his LAN from the router to all his devices then it would not work mixing a 10 with 192 network.
But he probably has it set correct and I got it wrong :-\
Oh we'll back to the amber nectar...
Dgd
I will start of by saying thanks for all the responses :) I woke up this morning and opened the( local App and it connected straight away to 10.0.0.10. SO I guess the classic auto reset overnight.
The way my network is set up is a little complex (sounds complex but is reasonably simple)
I have our main modem/router at one end of the. A 4 port wifi router located in the centre of the house connected via a lan cable to the main modem/router. The 2nd wifi / router is also a lan over power line device . I then have the receiver for the lan over power line plunged into a power outlet near the classic and a lan cable from the receiver to the classic :o
All my local devices, laptop, i phone, I pad, desktop pc, have all been handed out a ip from 10.0.0.0 up to 10.0.0.13 at the moment.Although using (Fling) my main router is showing up as 10.0.0.137.
Kurt
Just a update on the 2nd issue not being able to connect to classic through local App over the internet.
I have it working now :)
Turns out it that my DNS software built into my Technicolor Gateway Router wasn't doing its job properly in updating the IP addresses to my Dyn host.
I gave up on using the routers in build DNS software and downloaded an update client program for my pc from Dyn and it did the trick local App connected over the net first time.
Kurt
Can you elaborate on how you fixed this as i'm having the same problem. Worked for a few days and now can't connect!!
Quote from: dgd on April 19, 2013, 07:48:31 AM
Quote from: offgridQLD on April 19, 2013, 07:25:29 AM
I have classic set on static ip 10.0.0.10 and I can see the classic on my network by y logging into my modem and its showing the some ip on the classic LCD. I also double checked the ip using the Fing program and its also showing the classic online on my local network at 10.0.0.10 and port 502.
Local networks should be on a 192.168.x.x network, internal routers, wifi routers and most other devices not assigned specific ip numbers or class c networks or subsets of them by your ISP will expect to use a 192.168.x.x network.
"classful" routing died years and years ago. 192.168.x.x networks are no less valid than 10.x.x.x networks, and a great many consumer devices ship with 10.x.x.x addresses by default.
Quote
Quote
So I open the local App enter 10.0.0.10 and and it comes up with (connecting) then (retrying) and (unknown) above the IP address .
The wifi router or LAN router you have will be trying to route this connection to the Internet where the real 10.x.x.x class A network is
He hasn't said what his computers network is (or if he did I missed it). His router would only be sending it outside if (a) his local subnet wasn't the same 10.x.x.y and (b) he didn't have a static route. (Granted, that seems unlikely for the average punter, but it's entirely valid and works perfectly well)
Just installed a new Classic 200. A small emergerncy back-up system for when the grid goes down. Four Evergreen 210W panels (2 x 2), to the Classic, to six Exide GC batteries (3 sets of 2), to a 1500W pure sine wave inverter. Everything seems to be working well. Except . . . .
Local App 0.3.27 does not connect to the Classic. Local App. Panel is blank. Classic picked up a valid LAN IP from the DHCP table and is shown on the Classic panel, and the router shows “Classic†in the client table. I am able to ping the classic address.
Any ideas?
You may try rebooting the Classic and see if it comes back
Ryan
I can't find “reboot†in the User's Manual. Do you mean to turn off the solar panels and then the batteries, then turn on the battery bank and then the solar panels? Did that, no joy.
Or do you mean a system reset to factory default with the left-right buttons held down during a power up?
Theres a certain way you have to hold your mouth to get the ethernet working on the classic.
First make sure you have the latest stable firmware. The latest adobe air, the latest local app.
Reboot, means unpower and repower the classic, maybe 10 seconds off ought to do it. After a firmware upgrade you also need to "VMM" which is a factory reset.
Second, make sure you use a short cable from the classic to the next network device. Long cables are a source of noise.
Third, i suggest using a static ip. The less you ask the classic to do the better, its only a tiny processsor, and needs its attention on your batterys.
Most people find that doing all that results in a stable connection.
:-\
Now I am even more confused, if that is possible. Checked firmware version on Classic = 1470. Latest Beta is 1401? tried to update any way to see what would happen and can't get USB connection to work, drivers not installed per Device Manager, Win XP Pro. Device Manager shows Bootloder ver. 1.06 for USB with question mark.
If you are using Windows XP you will need to install the drivers and set the com port of the PC to Com8. There is a pretty decent document on doing this on XP here: http://www.midnitesolar.com/firmware/Firmware_Install_WindowsXP.pdf (http://www.midnitesolar.com/firmware/Firmware_Install_WindowsXP.pdf)
:)
OK. Making progress. Panel still not working, but firmware is current at 1401 and MNGP at 1370. Thanks for the detailed PDF. The only detail I was missing was where to browse for the driver.
Removed and re-installed Abobe Air and Status Panel. No joy!
What's next?
Hi, A1,
Sorry for the network troubles.
Can I just get another run down on the system to make sure we've got everything in place:
- Classic set to DHCP or Static?
- You may want to set it to Static to avoid any other problems.
- Is the application set to "Automatically detect classics?"
- Are you running a firewall on your computer? If so have you opened the port corresponding to your Classic (502 by default) or have you made an exception to let the local application bypass the firewall?
- Is the Classic running on a separate subnet? If so the UDP advertise packets will not be able to get to the Local App and it will not detect.
- Do you have a high-traffic network? Dropbox or bit torrent apps tend to destroy my network.
- what model of router/switch are you using? Some older switches have to be rebooted when new devices are added or on occasion.
- Is anything else attaching to the Classic on your network? It's a long-shot, sure...
- Are you running the latest version of Adobe AIR? Might be worth an update if you haven't already.
That's all I can think of off the top of my head. Local App has been behaving pretty well last few revs.
;D
As Homer would say, "Doh!", or as I would say back when I worked the Tech Phones, "It's so obvious once you figure it out." It was the old "ID 10 T" error.
I did not put the IP in the app configure field because I ASSUMED the app would find the Classic if the Auto Detect box was checked.
Thanks for all the help with the new kid on the block.
But, this brings up another question. On my LAN I'm running a desktop, two printers, and the Classic hard wired to a four port Belkin wireless router. Also, running two laptops and an iPad on the wire less side. All running DHCP except the printers which are static IPs.
As these devices are powered up and down though out the day as needed, there is a good chance the Classic will pick up a different IP in the future. Therefore, as noted in several other posts, would it be wise to give the Classic a static IP outside the DHCP table? I am inclined to say "Yes" and give the Classic a static IP.
AHA!
Yes, I'd say that a static IP is probably the best. DHCP is designed to pick up the last IP used when available, but this really depends on the implementation of the server software and not all DHCP server honor this. The Classic tries to claim its last address but this is touch and go on different systems.
I'd definitely go for a static IP in most cases -- DHCP is great for "plug-and-go" when it works, but if you want the Classic on your network where you can always find it, ya can't beat the static.
Quote from: atop8918 on August 31, 2013, 03:24:19 PM
DHCP is great for "plug-and-go" when it works, but if you want the Classic on your network where you can always find it, ya can't beat the static.
Unless, like me, you have >100 active devices on your network as well as lots of roaming/visiting devices, and trying to maintain them all as statics is just a PITA. Then, letting DHCP do all the work, maintaining a central config that gives fixed addresses to the 60 or so that need them and having it right there in front of you is a real bonus.
Good point!