Firmware incompatibilities?

Started by krementz, October 10, 2020, 04:23:22 PM

Previous topic - Next topic

krementz

I have had 3 Classics running for several years. I installed an additional 4kw of PV and a new Classic. These are all going into a dual SMA 6048 Sunny Island inverter.

I can't get the four Classics to play nice. There is a communication problem between them and the SMA.

The 3 older Classics are all running firmware. The old ones are running 2126,  the new one 2193. Does anyone know if there are any issues running this combination of firmware?

My understanding is the only difference between them is the talk "feature". Can anybody verify it? i really do not want to be forced to update all 4 boxes to talkies.
Way off grid
Old system: Outback 2524, 1200 W PV,  installed 2005, 384 amp hours
New System: 2 SMA 6048 with 2 Midnite Solar Classic 150 controllers, 5500 W PV, 1700 amp hours

Vic

#1
Hi krementz,

According to the MN Solar site,  2193 is still the latest:

http://www.midnitesolar.com/firmwareReport.php?firmware_ID=19&firmwareProduct_ID=1&act=edit

The speech firmware is still considered Beta:
http://midniteftp.com/forum/index.php?topic=4212.msg41349#msg41349

The above Link was from a Post by Classic Crazy Larry.

There has been some discussion of SMA Si inverters with the MN Combox,   see Post #22 & 23, (and perhaps others) here:
http://midniteftp.com/forum/index.php?topic=5000.15

I know nothing of these items,  when connected together.   Good luck,   VIc
Off Grid - Sys 1: 2ea SW+ 5548, Surrette 4KS25 1280 AH, 5.25 KW PV, Classic 150,WB, Beta Barcelona, Beta KID
Sys 2: SW+ 5548s, 4KS25s, 5.88 KW PV, 2 ea. Classic 150, WB, HB CC-needs remote Monitoring/Control, site=remote.
 MN Bkrs/Bxs/Combiners. Thanks MN for Great Products/Svc/Support&This Forum!!

ClassicCrazy

#2
I would want to have them all on the same newest firmware . I don't know if that is the problem but that is where I would start .
There may have been other changes in the firmware too.

The SMA thread that Vic linked above has details on setting the Classic addresses and having to use the MNGP to do that instead of using the Local Status app.

Larry
system 1
Classic 150 , 5s3p  Kyocera 135watt , 12s Soneil 2v 540amp lead crystal 24v pack , Outback 3524 inverter
 5s 135w Kyocero , 3s3p 270w Kyocera   Classic 150 ,8s2p  Kyocera 225w to Hawkes Bay Jakiper 48v 20kwh  ,Gobel 16 kwh  lifepo4 Outback VFX 3648  8s2p 380w Rec pv EG4 6000XP

boB


I  ~think~  that 2126 should be good for SMA ?

Somewhere on here there is a Classic software revision list... up to a certain point anyway.

In the MNGP menu under COM (?) there is a setting for SMA mode.   Is that set ?

boB
K7IQ 🌛  He/She/Me

krementz

I know 2193 is the latest firmware.

My other three Classics have 2126.

I am asking if there are specific compatibilities issues in Modbus  between the two versions. I would rather roll back the new Classic to 2126 than update the other three to 2193.
Way off grid
Old system: Outback 2524, 1200 W PV,  installed 2005, 384 amp hours
New System: 2 SMA 6048 with 2 Midnite Solar Classic 150 controllers, 5500 W PV, 1700 amp hours

FNG

There should be no reason they wouldnt play together. I would call in to support for assistance it almost sounds like a bad cable or jack or something