update error in status panel

[dbcollen]

Ever since I updated to 0.2.7 on the status panel I get this error every morning.

[StatusUpdateErrorEvent (type=updateError text=Error #3013 id=16818 + subErrorID=3013)]

Dustin

[dbcollen]

Also the PCB temps seem high, it reads 104.7f while it is resting at night in a 60f basement. FET is 84.9f, Bat is 69.8f.

Dustin

[mtdoc]

I get the same error message daily.

Also, I have similar temps as yours -I  assumed that was normal - maybe not??

[epsgunner]

Thats odd I just downloaded Local Status Panel 0.2.4 about 2-3 weeks back...

Are you talking the LAN version for the desktop?? or the controller MNGP??

Are they up to 0.2.7??

[dbcollen]

the desktop version, and yes, they are up to 0.2.7 try to manually update from inside the program.

[boB]

Also the PCB temps seem high, it reads 104.7f while it is resting at night in a 60f basement. FET is 84.9f, Bat is 69.8f.

Dustin

That is kind of weird but  OK.     Is this only on the Local App ??    What if you go look in the Classic TEMPS menu itself ??
Of course the numbers in the Classic will be in C, not F.  I am always used to seeing the degrees in C and not F.

Maybe the higher ambient temperature along with the internal temperature raises it up just a bit ?

What is the temperature inside the room ? 

boB

[dbcollen]

I will check the temps on the classic when it is resting this evening, the room it is in is 55-65f year round. Presently it is putting out 1100W and the temps are: Temperature: FET: 113.9°F     PCB: 122.2°F BAT: 71.1°F

[boB]

I will check the temps on the classic when it is resting this evening, the room it is in is 55-65f year round. Presently it is putting out 1100W and the temps are: Temperature: FET: 113.9°F     PCB: 122.2°F BAT: 71.1°F

OK, that is 113.9 F is  45 C   which is just fine for 1100 watts.

We'll check back later for the night time temperature.

boB

[dbcollen]

ok, the status panel says: FET: 89.1°F     PCB: 110.1°F    BAT: 75.7°F     The classic says:PCB:43.2c   Bat 24.3c

[boB]

ok, the status panel says: FET: 89.1°F     PCB: 110.1°F    BAT: 75.7°F     The classic says:PCB:43.2c   Bat 24.3c

It may take a while for it to cool down more but that it might be an older control board where the regulator runs daughter and spillingover to the FET Temperature.  Check them even that much later After it has turned off.  If this has been an hour or more than  you probably stable.

[dbcollen]

the first reported temp of 104.7f was at 06:00 before the machine woke up. My main question was about that annoying update error.

[dbcollen]

I set the update interval to 7 days, and havn't seen the error again. It should try to update again in a few days.

[mtdoc]

Where does is allow you to adjust the update interval?

Oops - never mind - I found it. Thanks!

[dbcollen]

Well, 7 days have passed and it tried to update again, Error [StatusUpdateErrorEvent (type=updateError text=Error #3013 id=16818 + subErrorID=3013)] Any ideas guys?

[epsgunner]

I just updated from inside to 0.2.7 version.. it gave me an update error when loading.. but still updated.. I dunno..   

It opens up and seems to work..